OVP Peripheral Model: XilinxZynq7000Usb
Model Specific Information
This page provides introductory usage information for an Imperas OVP peripheral behavioral model.
The page is split into sections providing specific information for this peripheral,
including any ports for connecting into a platform, registers, other component parts, and configuration options and general information for peripheral modeling with Imperas OVP.
Description
Zynq 7000 USB Registers
Licensing
Open Source Apache 2.0
Limitations
This model implements the full set of registers but no behavior.
Reference
Zynq-7000 TRM (https://www.xilinx.com/support/documentation/user_guides/ug585-Zynq-7000-TRM.pdf)
Location
The zynq_7000-usb peripheral model is located in an Imperas/OVP installation at the VLNV: xilinx.ovpworld.org / peripheral / zynq_7000-usb / 1.0.
Net Ports
This model has the following net ports:
Table : Net Ports
Name | Type | Must Be Connected | Description |
---|
intOut | output | F (False) | |
Bus Slave Ports
This model has the following bus slave ports:
Bus Slave Port: bport1
Table 1: Bus Slave Port: bport1
Name | Size (bytes) | Must Be Connected | Description |
---|
bport1 | 0x1000 | T (True) | |
Table 2: Bus Slave Port: bport1 Registers:
Name | Offset | Width (bits) | Description | R/W | is Volatile |
---|
ab_ID | 0x0 | 32 | IP version and revision, read-only | | |
ab_HWGENERAL | 0x4 | 32 | Misc IP config constants, read-only | | |
ab_HWHOST | 0x8 | 32 | Host Mode IP config constants, read-only | | |
ab_HWDEVICE | 0xc | 32 | Device Mode IP config constants, read-only | | |
ab_HWTXBUF | 0x10 | 32 | TxBuffer IP config constants, read-only | | |
ab_HWRXBUF | 0x14 | 32 | IP constants, RX buffer constants, read-only | | |
ab_GPTIMER0LD | 0x80 | 32 | GP Timer 0 Load Value | | |
ab_GPTIMER0CTRL | 0x84 | 32 | GP Timer 1 Control | | |
ab_GPTIMER1LD | 0x88 | 32 | GP Timer 1 Load Value | | |
ab_GPTIMER1CTRL | 0x8c | 32 | GP Timer 1 Control | | |
ab_SBUSCFG | 0x90 | 32 | DMA Master AHB Burst Mode | | |
ab_CAPLENGTH_HCIVERSION | 0x100 | 32 | EHCI Addr Space and HCI constants, read-only | | |
ab_HCSPARAMS | 0x104 | 32 | TT counts and EHCI HCS constants, read-only | | |
ab_HCCPARAMS | 0x108 | 32 | EHCI Host configuration constants | | |
ab_DCIVERSION | 0x120 | 32 | Device Mode CI version constant | | |
ab_DCCPARAMS | 0x124 | 32 | EHCI, device and endpoint capabilities | | |
ab_USBCMD | 0x140 | 32 | USB Commands (EHCI extended) | | |
ab_USBSTS | 0x144 | 32 | Interrupt/Raw Status (EHCI extended) (Host/Device) | | |
ab_USBINTR | 0x148 | 32 | Interrrupts and Enables | | |
ab_FRINDEX | 0x14c | 32 | Frame List Index | | |
ab_PERIODICLISTBASE_DEVICEADDR | 0x154 | 32 | Host/Device Address dual-use | | |
ab_ASYNCLISTADDR_ENDPOINTLISTADDR | 0x158 | 32 | Host/Device dual-use | | |
ab_TTCTRL | 0x15c | 32 | TT Control | | |
ab_BURSTSIZE | 0x160 | 32 | Burst Size | | |
ab_TXFILLTUNING | 0x164 | 32 | TxFIFO Fill Tuning | | |
ab_TXTTFILLTUNING | 0x168 | 32 | TT TX latency FIFO | | |
ab_IC_USB | 0x16c | 32 | Low and Fast Speed Control constants | | |
ab_ULPI_VIEWPORT | 0x170 | 32 | ULPI Viewport | | |
ab_ENDPTNAK | 0x178 | 32 | Endpoint NAK (Device mode) | | |
ab_ENDPTNAKEN | 0x17c | 32 | Endpoint NAK (Device mode) | | |
ab_CONFIGFLAG | 0x180 | 32 | reserved | | |
ab_PORTSC1 | 0x184 | 32 | Port Status & Control | | |
ab_OTGSC | 0x1a4 | 32 | OTG Status and Control | | |
ab_USBMODE | 0x1a8 | 32 | USB Mode Selection | | |
ab_ENDPTSETUPSTAT | 0x1ac | 32 | Endpoint Status Setup (Device mode) | | |
ab_ENDPTPRIME | 0x1b0 | 32 | Endpoint Primer (Device mode) | | |
ab_ENDPTFLUSH | 0x1b4 | 32 | Endpoint Flush (Device mode) | | |
ab_ENDPTSTAT | 0x1b8 | 32 | Endpoint Buffer Ready Status (Device mode), RO | | |
ab_ENDPTCOMPLETE | 0x1bc | 32 | Endpoint Tx Complete (Device mode) | | |
ab_ENDPTCTRL0 | 0x1c0 | 32 | Endpoint 0 (Device mode) | | |
ab_ENDPTCTRL1 | 0x1c4 | 32 | Endpoints 1 to 11 (Device mode) | | |
ab_ENDPTCTRL2 | 0x1c8 | 32 | Endpoints 1 to 11 (Device mode) | | |
ab_ENDPTCTRL3 | 0x1cc | 32 | Endpoints 1 to 11 (Device mode) | | |
ab_ENDPTCTRL4 | 0x1d0 | 32 | Endpoints 1 to 11 (Device mode) | | |
ab_ENDPTCTRL5 | 0x1d4 | 32 | Endpoints 1 to 11 (Device mode) | | |
ab_ENDPTCTRL6 | 0x1d8 | 32 | Endpoints 1 to 11 (Device mode) | | |
ab_ENDPTCTRL7 | 0x1dc | 32 | Endpoints 1 to 11 (Device mode) | | |
ab_ENDPTCTRL8 | 0x1e0 | 32 | Endpoints 1 to 11 (Device mode) | | |
ab_ENDPTCTRL9 | 0x1e4 | 32 | Endpoints 1 to 11 (Device mode) | | |
ab_ENDPTCTRL10 | 0x1e8 | 32 | Endpoints 1 to 11 (Device mode) | | |
ab_ENDPTCTRL11 | 0x1ec | 32 | Endpoints 1 to 11 (Device mode) | | |
Platforms that use this peripheral component
Peripheral components can be used in many different platforms, including those developed by Imperas or by other users of OVP. You can use this peripheral in your own platforms.
Table 3: Publicly available platforms using peripheral 'zynq_7000-usb'